Electric Outboard Motor, 40 lbs Thrust Electric Trolling Motor with 5 Forward & 3 Reverse Gears for Fishing Boats, Dinghies, and Inflatable Boats

The trolling motor is made of pure copper, which has excellent electrical conductivity, thermal conductivity, ductility and corrosion resistance. Meanwhile, it can overcome huge water resistance to increase the speed of driving. Its angle, gear, and height can all be freely adjusted. It is suitable for a variety of small watercraft, such as fishing boats, dinghies, and inflatable boats.DetailsTightened Brackets: The tightened brackets are used to secure the thrusters and transoms of the ship so that the thruster will not fall from your boats.High Power Battery Clamp: The clamp is more durable and wear-resistant under high currents. And they have good conductivity.Circuit Breaker Protector: The trolling motor with overload, short-circuit, and under-voltage protection settings can protect wiring and power.ApplicationThe trolling motor is suitable for a variety of small watercraft, such as fishing boats, dinghies, and inflatable boats.SpecificationModel: L40Speed Control: F5-R2Motor Type: Brush MotorRated Voltage(V): 12Rated Speed(R/min): 1700Rated Current(A): 34Rated Power(W): 408Control Handle: Retractable Maximum Speed(km/h): 6Noise: 50dbUltimate Thrust: 300kg/661 lbsBattery Model: 12V 100A BatteriesNet Weight: 7.8kg/17.2lbsGross Weight: 9.3kg /20.5lbsPropeller Model: 3 Leaves, 7.6*22.9cm/3*9inRod Length: 76cm/30inchPacakge Size: 102*41*16cm (40.16*16.14*6.30inch)Installation1. Tear off the sticker at the spring on the handle.2. Take out the handle, and align the handle with the interface at the inner shell of the handle.3. Press the handle spring with one hand and push the handle in with the other hand. After a crunching sound is heard, the handle is installed.4. Take out the cylindrical card pin and insert it into the round hole of the drive rod (note that the length of both ends needs to be consistent).5. Align the back of the propeller with the card slot and the card pin horizontally, and then tap into the propeller with force.6. Put in the card flap, then screw the nut to complete the installation.7. Take the fins out of the box and insert them into the fin slot. 8. Put the included screws into the screw holes of the fins and put the nuts into the other end. Hold them down.9. Then tighten the screws with the Phillips screwdriver.10. If you have any problems, please feel free to contact us. We will reply and solve the problem for you as soon as possible.Package Included1*Trolling Motor1*Power Propeller1* Circuit Breaker Protector1*Battery Clamp1 Set of Screws1*English ManualNotes1.Please read the attached manual completely before use. And pay particular attention to the safety instructions included. 2.Don't start the motor on the bank. If you want to test the motor, it should be done in the river.3.Don't use the motor when no water comes out of it, and then check whether the pump impeller or the water outlet is blocked.4.Do not switch gears too quickly. You should switch from one gear to another.5.Be sure the switch is in the OFF position before the connection to the battery.6.Always disconnect power when replacing the propeller, removing debris around the propeller, charging batteries, transporting a boat, or when the motor is not in use. 7.Remember always disconnect from batteries once the motor leaves water as a rotating propeller can cause personal injury.8.Electrical arcing near the battery could ignite hydrogen gas and cause the battery to explode.9.Please wash the motor with freshwater, so that it can greatly reduce the possibility of corrosion.10.All trolling motors have noise. And the noise of this motor is the same as a motorcycle, which is normal.11.The trolling motor is recommended for thrusting small boats under 200kg/440lbs. 12.You must prepare a boat motor bracket or lifting board on your boat. 13.The battery is not included in the package.14.Please choose 12V 100A battery so that the maximum power can be guaranteed for 3 hours of continuous operation.

• High Efficiency: The trolling motor is made of pure copper, which has excellent electrical conductivity, thermal conductivity, ductility and corrosion resistance. It can overcome huge water resistance to increase the speed of driving and improve its efficiency.
• Real-time Monitoring of Power: The top of the thruster has a real-time display of the battery power, allowing you to check the power situation any time and prepare for charging in advance to avoid running out of power in the middle of the voyage.
• Easy to Drive: The main rod is made of aluminum. Its lightweight will not increase the entire weight of your boat and the difficulty of driving. The fixed tiller has 5 forward and 3 reverse speeds. You can smoothly switch the speed and change the direction during driving. Its depth and angle can be freely adjusted according to the actual situation and your special needs.
• Details: The tightened brackets are used to secure the thrusters and transoms of the ship so that the thruster will not fall from your boats. The high power battery clamp is more durable and wear-resistant under high currents. And they have good conductivity.
• Circuit Breaker Protector: The trolling motor with overload, short-circuit, and under-voltage protection settings can protect wiring and power.